德源科技 
德源科技德源科技
公司簡介訂購方式匯款確認檔案下載 聯絡我們保固說明訂單查詢討論區
電子郵件:

密碼:

忘記密碼
加入會員
  首頁 | 原廠 Arduino® | 特殊服務設計 | 轉接座及轉接板/麵包板 | 開發板/燒錄器/模擬器 | 相容 For Arudino® 週邊及配件 | OKdo系列 | Saleae 系列 | Adafruit 系列 | ArduCam 系列 | Camera 攝像頭 | ROCK 系列 | Debix系列開發板 | Raspberry Pi 樹莓派 | Banana Pi 香蕉派 | BeagleBone 狗骨頭 | M5Stack系列 | Micro:bit (BBC)系列 | NVIDIA Jetson Nano系列 | Pololu 系列 | Pycom 系列 | Seeed 系列 | Sparkfun 系列 | WeMos 系列 | 傳感器 | Cubieboard/CubieTruck系列 | Firefly 系列 | Microduino系列 | Orange Pi 香橙派 | PCB板 | PLC 系列 | Robot 機器人 | UDOO 系列 | RedBearLab 系列 | LattePanda系列 | LittleBits 系列 | Libelium 系列 | Luxonis 相機系列 | PCduino | RobotElectronics 系列 | MageDok 顯示屏 | LCD/LCM/TFT/LVDC | Dimension Engineer 系列 | 通訊模組 | 影音器材(含轉換器) | 線材/連結器/轉換器 | 測量儀器 | 馬達/馬逹控制器/電源模組 | 其他 | 焊接/維修工具 | IC零件 | LED燈-裝飾燈 | 工作站迷你電腦 mini PC | 擴大器 | 雕刻機 | 電池 | 電腦周邊 | 檢定考套件 | 停售商品
  首頁 » 商品目錄 » 原廠 Arduino® » Original Arduino®(義大利原廠) 主板 » A000022
商品搜尋 進階
 |  購物車內容  |  結帳   
商品分類
  Original Arduino®(義大利原廠) 主板
  Original Arduino®(義大利原廠) 套件
  Original Arduino®(義大利原廠) 擴展板
  Original Arduino®(義大利原廠) 配件
Arduino
Pololu
Seeed
Sparkfun
robot-electronics
dimensionengineering
libelium
adafruit
udoo
redbearlab
Arducam
goembed
Saleae
okdo
服務台
公司簡介
退換貨服務
訂購方式
聯絡我們
匯款確認
[<< 前一頁]  瀏覽相同分類產品 23 / 48  [下一頁 >>]
>(停產)Arduino® Leonardo ETH 不帶POE (A000022)(義大利原廠)
NT$9,999
運費NT$50
條碼A000022
產品說明0

 ※本產品原廠代理從國外進口,有些交期較長,下訂前請詢問!

 Arduino Leonardo ETH (without PoE) (A000022)

  A000022 (without PoE) 不帶POE

 A000023 (with PoE) 帶POE 

Overview

       The Leonardo ETH is a microcontroller board based on the ATmega32U4 (datasheet) and the new W5500 TCP/IP Embedded Ethernet Controller (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a RJ45 connection, a micro USB connector, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

      The Leonardo ETH differs from the preceding Ethernet board in that the ATmega32u4 has built-in USB communication, eliminating the need for an external USB-to-serial converter. This allows the Leonardo ETH to appear to a connected computer as a mouse and keyboard, in addition to a virtual (CDC) serial / COM port. It also has other implications for the behaviour of the board. Plus, it has the new W5500 TCP/IP Embedded Ethernet Controller onboard.

      An optional Power over Ethernet module can be added to the board as well.
The Leonardo ETH has the same Wiznet Ethernet interface as the Ethernet Shield 2.

      An onboard microSD card reader, which can be used to store files for serving over the network, is accessible through the SD Library. Pin 10 is reserved for the Wiznet interface, SS for the SD card is on Pin 4.
The board uses the standardized 1.0 pinout, consisting of:

added SDA and SCL pins: beside the AREF pin, two TWI pins have been added. This will allow to connect the Leonardo ETH to Shields that use the I2C or TWI bus communication for their functioning.

the IOREF: it allows the shields to adapt to the IO voltage level provided by the Board. The Shield that uses the IOREF pin will be compatible with both 3V3 and 5V (e.g Due and Uno) IO levels Arduino Boards. Next to the IOREF pin you can find another (currently not in use) pin, that is reserved for future usage. 

Summary

       
 Microcontroller  ATmega32u4
 Operating Voltage  5V
 Input Voltage Plug (recommended)  7-12V
 Input Voltage Plug (limits)  6-20V
 Input Voltage PoE (limits)  36-57V
 Digital I/O Pins  20
 PWM Channels   7
 Arduino Pins reserved

 4 used for SD card select

 10 used for W5500 select

 Analog Input Pins  12
 DC Current per I/O Pin  40 mA
 DC Current for 3.3V Pin  1 A (only when powered via the external power supply)
 Flash Memory  32 KB (ATmega32u4) of which 4 KB used by bootloader
 SRAM  2.5 KB (ATmega32u4)
 EEPROM  1 KB (ATmega32u4)
 Clock Speed  16 MHz
W5500 TCP/IP Embedded Ethernet Controller
Power Over Ethernet ready Magnetic Jack
Micro SD card, with active voltage translators

Schematic & Reference Design

EAGLE files: Arduino-Leonardo-ETH-XX-reference-design.zip
Schematic: Arduino-Leonardo-ETH-XX-schematic.pdf

Power

      The board can be powered also via an external power supply, via an optional Power over Ethernet (PoE) module, or using the micro USB connection. 

    External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. When using the power adapter, it can be connected by plugging a 2.1mm center-positive plug into the board's power jack. Leads from a battery can be inserted in the Gnd and Vin pin headers of the POWER connector.

    The board can operate on an external supply of 6 to 20 volts. If supplied with less than 7V, however, the 5V pin may supply less than five volts and the board may be unstable. If using more than 12V, the voltage regulator may overheat and damage the board. The recommended range is from 7 to 12 volts.

The power pins are as follows:

  • VIN. The input voltage to the Arduino board when it's using an external power source (as opposed to 5 volts from the USB connection or other regulated power source). You can supply voltage through this pin, or, if supplying voltage via the power jack, access it through this pin.
  • 5V. This pin outputs a regulated 5V from the regulator on the board. The board can be supplied with power either from the DC power jack (7 - 12V), the USB connector (5V), or the VIN pin of the board (7-12V). Supplying voltage via the 5V or 3.3V pins bypasses the regulator, and can damage your board. We don't advise it.
  • 3V3. A 3.3 volt supply generated by the on-board regulator. Maximum current draw is 50 mA.
  • GND. Ground pins.
  • IOREF. This pin on the Arduino board provides the voltage reference with which the microcontroller operates. A properly configured shield can read the IOREF pin voltage and select the appropriate power source or enable voltage translators on the outputs for working with the 5V or 3.3V.

The optional PoE module is designed to extract power from a conventional twisted pair Category 5 Ethernet cable.

    PoE module features are as follows: 

  • IEEE802.3af compliant
    Input voltage range 36V to 57V
    Overload and short-circuit protection
    12V Output
    High efficiency DC/DC converter: typ 85% @ 80% load
    1500V isolation (input to output)

Memory

      The ATmega32u4 has 32 KB (with 4 KB used for the bootloader). It also has 2.5 KB of SRAM and 1 KB of EEPROM (which can be read and written with the EEPROM library).

Input and Output

     Each of the 14 digital pins on the Leonardo ETH board can be used as input or output, using the pinMode(), digitalWrite(), and digitalRead() functions. They operate at 5 volts. Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor (disconnected by default) of 20-50 kOhms. In addition, some pins have specialized functions:

  • Serial: 0 (RX) and 1 (TX): used to receive (RX) and transmit (TX) TTL serial data using the ATmega32U4 hardware serial capability. Note that on the Leonardo ETH, the Serial class refers to USB (CDC) communication; for TTL serial on pins 0 and 1, use the Serial1 class.
  • TWI: 2 (SDA) and 3 (SCL): they support TWI communication using the Wire library.
    External Interrupts: 3 (interrupt 0), 2 (interrupt 1), 0 (interrupt 2), 1 (interrupt 3) and 7 (interrupt 4). These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. See the attachInterrupt() function for details.
  • PWM: 3, 5, 6, 9, 10, 11 and 13. Provide 8-bit PWM output with the analogWrite() function.
  • SPI: on the ICSP header. These pins support SPI communication using the SPI library. Note that the SPI pins are not connected to any of the digital I/O pins as they are on the Uno, They are only available on the ICSP connector. This means that if you have a shield that uses SPI, but does NOT have a 6-pin ICSP connector that connects to the Leonardo's 6-pin ICSP header, the shield will not work.
  • LED: 13. There is a built-in LED connected to the digital pin 13. When the pin is HIGH value, the LED is on, when the pin is LOW, it's off.
  • Analog Inputs: A0-A5, A6 - A11 (on digital pins 4, 6, 8, 9, 10, and 12). The Leonardo has 12 analog inputs, labeled A0 through A11, all of which can also be used as digital i/o. Pins A0-A5 appear in the same locations as on the Uno; inputs A6-A11 are on digital i/o pins 4, 6, 8, 9, 10, and 12 respectively. Each analog input provides 10 bits of resolution (i.e. 1024 different values). By default, the analog inputs measure from ground to 5 volts, though it is possible to change the upper end of their range using the AREF pin and the analogReference() function.

There are a couple of other pins on the board:

AREF. Reference voltage for the analog inputs. Used with analogReference().

Reset. Bring this line LOW to reset the microcontroller. Typically used to add a reset button to shields that block the one on the board.

Communication

      The Arduino Leonardo ETH has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers.

    The ATmega32U4 provides UART TTL (5V) serial communication, which is available on digital pins 0 (RX) and 1 (TX). The 32U4 also allows for serial (CDC) communication over USB and appears as a virtual COM port to software on the computer. The chip also acts as a full speed USB 2.0 device, using standard USB COM drivers. On Windows, a .inf file is required. The Arduino software includes a serial monitor allowing simple textual data to be sent to and from the Arduino board.

    The RX and TX LEDs on the board will flash when data is being transmitted via the USB connection to the computer (but not for serial communication on pins 0 and 1).

    A SoftwareSerial library allows for serial communication on any of the Leonardo ETH's digital pins.

The ATmega32U4 also supports I2C (TWI) and SPI communication. The Arduino software includes a Wire library to simplify the use of the I2C bus. For SPI communication, use the SPI library.

    The Leonardo ETH appears as a generic keyboard and mouse, and can be programmed to control these input devices using the Keyboard and Mouse classes.

    The board can also connect to a wired network via Ethernet. When connecting to a network, you will need to provide an IP address and a MAC address. The Ethernet Library is fully supported.

    The onboard microSD card reader is accessible through the SD Library. When working with this library, SS is on Pin 4.

Programming

      The Leonardo ETH can be programmed with the Arduino software (download). Select "Arduino Leonardo ETH from the Tools > Board menu. For details, see the referenceand tutorials.

The ATmega32U4 on the Arduino Leonardo ETH comes pre-burned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the AVR109 protocol.

 

You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header using Arduino ISP or similar. 

 

All the Leonardo ETH example sketches work as they do with the Ethernet shield 2. Make sure to change the network settings for your network.

Automatic (Software) Reset

      Rather than requiring pressing the reset button before an upload, the Leonardo ETH is designed in a way that allows it to be reset by software running on a connected computer. The reset is triggered when the Leonardo's virtual (CDC) serial / COM port is opened at 1200 baud and then closed. When this happens, the processor will reset, breaking the USB connection to the computer (meaning that the virtual serial / COM port will disappear). After the processor resets, the bootloader starts, remaining active for about 8 seconds. The bootloader can also be initiated by pressing the reset button on the Leonardo. Note that when the board first powers up, it will jump straight to the user sketch, if present, rather than initiating the boot loader.

Because of the way the Leonardo ETH handles the reset, the best thing to do is to let the Arduino software try to initiate the reset before uploading, especially if you are used to pressing the reset button before uploading on other boards. If the software can't reset the board, you can always start the bootloader pressing the reset button on the board.

USB Overcurrent Protection

      The Leonardo ETH has a resettable polyfuse that protects your computer's USB ports from shorts and overcurrent. Although most computers provide their own internal protection, the fuse provides an extra layer of protection. If more than 500 mA is applied to the USB port, the fuse will automatically break the connection until the short or overload is removed. 

Physical Characteristics

      The maximum length and width of the Leonardo ETH PCB are 2.7 and 2.1 inches respectively, with the RJ45 connector and power jack extending beyond the former dimension. Four screw holes allow the board to be attached to a surface or case. Note that the distance between digital pins 7 and 8 is 160 mil (0.16"), not an even multiple of the 100 mil spacing of the other pins.

Product Code

A000022 (without PoE) 不帶POE
A000023 (with PoE) 帶POE 

問與答

目前沒有任何商品問答!
本商品上架日期:2013-08-28.
評價
購物車 更多
1 x ●MSP430開發板(DM430-L) MSP430F149單片機 小系統板核心板 彩屏帶USB下載器
1 x Raspberry Pi 樹莓派 Pi2 Pi3 適用(WPC-632-2-DIO84-AI)Web Based Program
1 x ARM CORTEX A8 TI OMAP3530開發板+5.6" LCD (devkit8000)
1 x ●10P 30cm 彩色 排線 公-公 / 雙公 / 公對公 散頭 杜邦線(10條一組)(PIGO)
1 x $ USB2.0開發板 FPGA+2SDRAM+USB2.0 數據採集 攝像頭 SENSOR
1 x ●電子半導體製冷套件 加熱製冷DIY 製冷降溫 風冷散熱 冷卻器配件2 / (附件請看詳細內容)
1 x ●樹莓派 Raspberry PI 攝像頭 360度 鵝頸套件V2 / 攝像頭支架 鵝頸支架(新板V3攝像頭適用)
1 x STC11F60XE 8位高性能單片機 單片機控制板 工控板 工業控制板 繼電器輸出控制板 仿PLC
1 x ●USB打印機共享器 USB切換器 2進1出 2口分線器 USB一拖二 手動切換(送線)
1 x B0032,Arducam原廠 OV5647攝像頭新版,帶4mm CS mount Lens 兼容樹莓派Pi3B+、Pi4B
1 x ARM Cortex-A8 Mini8600B核心板 TI AM3359處理器
1 x 原裝韓國 Tekcell SB-C02 圓柱 C型 2號 儀表控制器 3.6V PLC 鋰電池
1 x 500W 成品 低音炮功放板
1 x &(現貨)最新 Raspberry Pi 4 B (是新版Pi4B) 4GB V1.5 type-C (送贈品)
NT$225,791
查詢訂單狀態
 
請輸入您的訂單編號
商品通知狀態 更多
通知>(停產)Arduino® Leonardo ETH 不帶POE (A000022)(義大利原廠)
更新時通知我
推薦給朋友
 
推薦這個商品給朋友

聯絡方式:手機:0933807110 或 0968222607
E-mail:[email protected](主要信箱) & [email protected](次要) & [email protected] & [email protected] & [email protected]