德源科技 
德源科技德源科技
公司簡介訂購方式匯款確認檔案下載 聯絡我們保固說明訂單查詢討論區
電子郵件:

密碼:

忘記密碼
加入會員
  首頁 | 特殊服務設計 | 開發板/燒錄器/模擬器 | Adafruit系列 | Arducam系列 | Arduino系列 | Dimension Engineer系列 | Libelium系列 | LittleBits系列 | Pololu系列 | RedBearLab系列 | Robot 機器人 | RobotElectronics原廠 | Saleae系列 | Seeed系列 | Sparkfun系列 | UDOO系列 | 傳感器 | 通訊模組 | 擴大器 | 轉接座及轉接板/麵包板 | 影音器材(含轉換器) | 線材/連結器/轉換器 | PLC系列 | IC零件 | 測量儀器 | 焊接/維修工具 | 馬達/馬逹控制器/電源模組 | 檢定考套件 | LED燈-裝飾燈 | Banana Pi 香蕉派 | BeagleBone 狗骨頭 | Orange Pi 香橙派 | Raspberry Pi 樹莓派 | 攝像頭Camera | 工作站迷你電腦 | LCD/LCM/TFT/LVDC | 雕刻機 | 電腦周邊 | 其他 | 電池 | 停售商品
  首頁 » 商品目錄 » Pololu系列 » Motion Control Modules » 43516213
商品搜尋 進階
 |  購物車內容  |  結帳   
商品分類
  Electronics
  Mechanical Components
  Motion Control Modules
    RC Servo Controllers
  Robot Kits
  Sensors
Arduino
Pololu
Seeed
Sparkfun
robot-electronics
dimensionengineering
libelium
adafruit
udoo
redbearlab
Arducam
goembed
Saleae
服務台
公司簡介
退換貨服務
訂購方式
聯絡我們
匯款確認
[<< 前一頁]  瀏覽相同分類產品 5 / 33  [下一頁 >>]
●Dual VNH2SP30雙軸馬達驅動器 Motor Driver Carrier MD03A 散件(PI0708)
NT$2,200
運費NT$50
條碼43516213
產品說明1

※本產品原廠代理從國外進口,有些交期較長,下訂前請詢問!

Dual VNH2SP30雙軸馬逹驅動器 Motor Driver Carrier MD03A 散件(PI708)

Dual VNH2SP30 Motor Driver Carrier MD03A

If you are looking to drive two high-power motors through one compact unit, these dual VNH2SP30 motor driver carriers are perfect for you. With these boards, it’s easy to get a medium-sized, differential drive robot running in no time. For even better control, the VNH2 version includes current sensing and can operate a higher PWM frequency (20 KHz) than its VNH3 counterpart.

Overview

 

 

 

 

The Pololu dual high-power motor drivers are compact carriers for the VNH3SP30 and VNH2SP30 motor driver integrated circuits from ST. The board incorporates most of the components of the typical application diagram on page 8 of the VNH2SP30 datasheet, including pull-up and current-limiting resistors and a FET for reverse battery protection. (The current sense circuit might not be populated on the VNH3SP30 version of the board since only the VNH2SP30 supports current sense.) To keep the number of I/O lines down, the two enable/diagnostic lines on each chip are tied together. All you need to add is a microcontroller or other control circuit to turn the H-Bridges on and off.

Please note that we offer several other products based on these same chips, including single carrier boards for controlling one motor, the qik 2s12v10 dual serial motor controller, the TReX motor controller, the jrk 12v12 USB motor controller with feedback, and the Orangutan X2 robot controller. We also have a family of higher-power motor drivers that can deliver more current over a wider operating voltage range.

 

 

 

 In a typical application, the power connections are made on one end of the board, and the control connections are made on the other end. +5 volts must be supplied to the board through the smaller 0.1"-spaced pins; the input voltage is available at those pins as well, but the connection is not intended for currents exceeding a few amps. The diagnostic pins can be left disconnected if you do not want to monitor the fault conditions of the motor drivers. INA and INB control the direction of each motor, and the PWM pins turns the motors on or off. For the VNH2SP30 version, the current sense (CS) pins will output approximately 0.13 volts per amp of output current. If you want to add current sensing to the VNH3SP30 version, or if you want higher-accuracy current sensing with the VNH2SP30 version, please consider our ±30A ACS714 current sensor carrier.

 

 

 

The dual motor driver PCB includes provisions for installing up to three large capacitors to limit disturbances on the main power line. Two 10mm radial capacitors may be mounted between the motor driver ICs, and an axial capacitor may be mounted between the ICs and power connections. It is generally not necessary to use all three capacitors; two radial capacitors are included with each unit. For applications that require a low profile, a single capacitor can be installed on its side as shown in the picture to the right.

Note: A 15-pin male header, three 2-pin terminal blocks, and two electrolytic capacitors are included but not soldered onto the boards. No printed documentation is shipped with these items; please see the VNH3SP30 and VNH2SP30 datasheets linked under the Resources tab.

VNH3SP30 and VNH2SP30 Comparison

VNH3SP30 和 VNH2SP30 比較

 

VNH3SP30

VNH2SP30

操作支援電壓

5.5 – 36 V*

5.5 – 16 V

最大電流率

30 A

30 A

MOSFET阻抗 (per leg)

34 mΩ

19 mΩ

最大PWM 頻率

10 kHz

20 kHz

電流偵測

none

approximately 0.13 V/A

過電壓關閉

36 V*

16 V minimum (19 V typical)

20A過熱時間

8 seconds

35 seconds

15A過熱時間

30 seconds

150 seconds

無限時間操作電流

9 A

14 A


馬達驅動器: VNH2SP30
馬達數: 2
最小操作電壓: 5.5 V
最大操作電壓: 16 V
每個連續輸出電流: 14 A
每個峰值輸出電流 30 A
連續平行輸出電流: 25 A
最大PWM頻率: 20 kHz
反向電壓保護: Y

*Manufacturer specification. In our experience, shoot-through currents make PWM operation impractical above 16 V.
**Typical results using Pololu motor driver carrier with 100% duty cycle at room temperature.

Real-world power dissipation considerations

The motor drivers have maximum current ratings of 30 A continuous. However, the chips by themselves will overheat at lower currents (see table above for typical values). The actual current you can deliver will depend on how well you can keep the motor drivers cool. The carrier printed circuit board is designed to draw heat out of the motor driver chips, but performance can be improved by adding a heat sink. In our tests, we were able to deliver short durations (on the order of milliseconds) of 30 A and several seconds of 20 A without overheating. At 6 A, the chip gets just barely noticeably warm to the touch. For high-current installations, the motor and power supply wires should also be soldered directly instead of going through the supplied terminal blocks, which are rated for up to 15 A.

This product can get hot enough to burn you long before the chip overheats. Take care when handling this product and other components connected to it.

Many motor controllers or speed controllers can have peak current ratings that are substantially higher than the continuous current rating; this is not the case with these motor drivers, which have a 30 A continuous rating and over-current protection that can kick in as low as 30 A (45 A typical). Therefore, the stall current of your motor should not be more than 30 A. (Even if you expect to run at a much lower average current, the motor can still draw high currents when it is starting or if you use low duty cycle PWM to keep the average current down.)

 

 

Schematic of the Pololu Dual High Current Motor Driver Carrier

 

問與答

顯示 1 到 第1 (共 1 則 問與答) 總頁數:  1 
會員 威仁先生/小姐 詢問: 2014-08-29  11:07:14
問題: 我想要下單Dual VNH2SP30雙軸馬逹驅動器 Motor Driver Carrier MD03A
請問有貨嗎?或者是要等多久才可以出貨呢?謝謝
回覆: 大約二到三週
顯示 1 到 第1 (共 1 則 問與答) 總頁數:  1 
本商品上架日期:2013-05-23.
評價
購物車 更多
空的...
查詢訂單狀態
 
請輸入您的訂單編號
商品通知狀態 更多
通知●Dual VNH2SP30雙軸馬達驅動器 Motor Driver Carrier MD03A 散件(PI0708)
更新時通知我
推薦給朋友
 
推薦這個商品給朋友

聯絡方式:手機:0933807110 或 0968222607
E-mail:i0104@ms13.hinet.net(主要信箱) & i03070309@yahoo.com.tw(次要) & a_te0307@hotmail.com & A9215017@mail.ntust.edu.tw & r94922042@ntu.edu.tw