德源科技 
德源科技德源科技
公司簡介訂購方式匯款確認檔案下載 聯絡我們保固說明訂單查詢討論區
電子郵件:

密碼:

忘記密碼
加入會員
  首頁 | 原廠 Arduino® | 特殊服務設計 | 轉接座及轉接板/麵包板 | 開發板/燒錄器/模擬器 | 相容 For Arudino® 週邊及配件 | OKdo系列 | Saleae 系列 | Adafruit 系列 | ArduCam 系列 | Camera 攝像頭 | ROCK 系列 | Debix系列開發板 | Raspberry Pi 樹莓派 | Banana Pi 香蕉派 | BeagleBone 狗骨頭 | M5Stack系列 | Micro:bit (BBC)系列 | NVIDIA Jetson Nano系列 | Pololu 系列 | Pycom 系列 | Seeed 系列 | Sparkfun 系列 | WeMos 系列 | 傳感器 | Cubieboard/CubieTruck系列 | Firefly 系列 | Microduino系列 | Orange Pi 香橙派 | PCB板 | PLC 系列 | Robot 機器人 | UDOO 系列 | RedBearLab 系列 | LattePanda系列 | LittleBits 系列 | Libelium 系列 | Luxonis 相機系列 | PCduino | RobotElectronics 系列 | MageDok 顯示屏 | LCD/LCM/TFT/LVDC | Dimension Engineer 系列 | 通訊模組 | 影音器材(含轉換器) | 線材/連結器/轉換器 | 測量儀器 | 馬達/馬逹控制器/電源模組 | 其他 | 焊接/維修工具 | IC零件 | LED燈-裝飾燈 | 工作站迷你電腦 mini PC | 擴大器 | 雕刻機 | 電池 | 電腦周邊 | 檢定考套件 | 停售商品
  首頁 » 商品目錄 » Pololu 系列 » Motion Control Modules » PI1183
商品搜尋 進階
 |  購物車內容  |  結帳   
商品分類
  DRVXXXX系列
  Electronics
  G2 High-Power Motor Drivers
  Mechanical Components
  Motion Control Modules
    RC Servo Controllers
  Robot Kits
  Sensors
Arduino
Pololu
Seeed
Sparkfun
robot-electronics
dimensionengineering
libelium
adafruit
udoo
redbearlab
Arducam
goembed
Saleae
okdo
服務台
公司簡介
退換貨服務
訂購方式
聯絡我們
匯款確認
[<< 前一頁]  瀏覽相同分類產品 16 / 27  [下一頁 >>]
A4988 步進馬達驅動板 含穩壓 Stepper Motor Driver Carrier with Voltage Regu
NT$480
運費NT$50
條碼PI1183
產品說明0

※本產品原廠代理從國外進口,有些交期較長,下訂前請詢問!

The A4988 stepper motor driver carrier with voltage regulators is a breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver. The board has two voltage regulators (5 V and 3.3 V), eliminating the need for separate logic and motor supplies. The driver features adjustable current limiting, overcurrent and overtemperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 – 35 V and can deliver up to approximately 1 A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional cooling).

 

A4983/A4988 stepper motor driver carrier with voltage regulators with dimensions.

 

Overview

This product is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection; we therefore recommend careful reading of the A4988 datasheet (380k pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil (see the Power Dissipation Considerations section below for more information). Here are some of the driver’s key features:

  • Simple step and direction control interface
  • Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
  • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
  • Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
  • Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
  • Short-to-ground and shorted-load protection

This carrier has reverse power protection on the main power input and built-in 5 V and 3.3 V voltage regulators that eliminate the need for separate logic and motor supplies and let you control the driver with microcontrollers powered at 5 V or 3.3 V. We also sell a smaller, higher-performace version of the A4988 carrier without voltage regulators.

Like nearly all our other carrier boards, this product ships with all surface-mount components—including the A4988 driver IC—installed as shown in the product picture.

Some unipolar stepper motors (e.g. those with six or eight leads) can be controlled by this driver as bipolar stepper motors. For more information, please see the frequently asked questions. Unipolar motors with five leads cannot be used with this driver.

Included Hardware

The A4988 stepper motor driver carrier with voltage regulators comes with one 1×14-pin breakaway 0.1" male header and one 1×8-pin breakaway 0.1" male header. The headers can be soldered in for use with solderless breadboards or 0.1" female connectors. You can also solder your motor leads and other connections directly to the board.

 

 

Using the driver

 

Minimal wiring diagram for wiring a 5V microcontroller to an A4983/A4988 stepper motor driver carrier with voltage regulators (full-step mode).

 

Power connections

The driver requires a logic supply voltage (3 – 5.5 V) to be connected across the VDD and GND pins and a motor supply voltage (8 – 35 V) to be connected across VMOT and GND. The logic voltage can be supplied from an external source, such as that powering the logic of the rest of the system, or by jumpering the output of the 5 V or 3.3 V voltage regulator outputs to VDD. There are also surface-mount pads that allow VDD selection to be made by making a solder bridge across the appropriate pads. Note that the driver’s regulators can also be used to power other electronics in the system, such as the controlling MCU.

The motor power supply should be capable of delivering the expected currents for the stepper motors being used (peaks up to 4 A).

Motor connections

Four, six, and eight-wire stepper motors can be driven by the A4988 if they are properly connected; a FAQ answer explains the proper wirings in detail.

Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble.)

 

 

Step (and microstep) size

Stepper motors typically have a step size specification (e.g. 1.8° or 200 steps per revolution), which applies to full steps. A microstepping driver such as the A4988 allows higher resolutions by allowing intermediate step locations, which are achieved by energizing the coils with intermediate current levels. For instance, driving a motor in quarter-step mode will give the 200-step-per-revolution motor 800 microsteps per revolution by using four different current levels.

The resolution (step size) selector inputs (MS1, MS2, and MS3) enable selection from the five step resolutions according to the table below. MS1 and MS3 have internal 100kΩ pull-down resistors and MS2 has an internal 50kΩ pull-down resistor, so leaving these three microstep selection pins disconnected results in full-step mode. For the microstep modes to function correctly, the current limit must be set low enough (see below) so that current limiting gets engaged. Otherwise, the intermediate current levels will not be correctly maintained, and the motor will skip microsteps.

MS1 MS2 MS3 Microstep Resolution
Low Low Low Full step
High Low Low Half step
Low High Low Quarter step
High High Low Eighth step
High High High Sixteenth step

Control inputs

Each pulse to the STEP input corresponds to one microstep of the stepper motor in the direction selected by the DIR pin. Note that the STEP and DIR pins are not pulled to any particular voltage internally, so you should not leave either of these pins floating in your application. If you just want rotation in a single direction, you can tie DIR directly to VCC or GND. The chip has three different inputs for controlling its many power states: RST, SLP, and EN. For details about these power states, see the datasheet.

Current limiting

To achieve high step rates, the motor supply is typically much higher than would be permissible without active current limiting. For instance, a typical stepper motor might have a maximum current rating of 1 A with a 5Ω coil resistance, which would indicate a maximum motor supply of 5 V. Using such a motor with 12 V would allow higher step rates, but the current must actively be limited to under 1 A to prevent damage to the motor.

The A4988 supports such active current limiting, and the trimmer potentiometer on the board can be used to set the current limit. One way to set the current limit is to put the driver into full-step mode and to measure the current running through a single motor coil without clocking the STEP input. The measured current will be 0.7 times the current limit (since both coils are always on and limited to 70% of the current limit setting in full-step mode). Please note that changing the logic voltage, Vdd, to a different value will change the current limit setting since the voltage on the REF pin is a function of Vdd.

Another way to set the current limit is to measure the voltage on the REF pin and to calculate the resulting current limit (the current sense resistors are 0.05Ω). The current limit relates to the reference voltage as follows:

Current Limit = VREF × 2.5

So, for example, if the reference voltage is 0.3 V, the current limit is 0.75 A. As mentioned above, in full step mode, the current through the coils is limited to 70% of the current limit, so to get a full-step coil current of 1 A, the current limit should be 1 A/0.7=1.4 A, which corresponds to a VREF of 1.4 A/2.5=0.56 V. See the A4988 datasheet for more information.

Note: The coil current can be very different from the power supply current, so you should not use the current measured at the power supply to set the current limit. The appropriate place to put your current meter is in series with one of your stepper motor coils.

Power dissipation considerations

The A4988 driver IC has a maximum current rating of 2 A per coil, but the actual current you can deliver depends on how well you can keep the IC cool. The carrier’s printed circuit board is designed to draw heat out of the IC, but to supply more than approximately 1 A per coil, a heat sink or other cooling method is required.

This product can get hot enough to burn you long before the chip overheats. Take care when handling this product and other components connected to it.

Please note that measuring the current draw at the power supply will generally not provide an accurate measure of the coil current. Since the input voltage to the driver can be significantly higher than the coil voltage, the measured current on the power supply can be quite a bit lower than the coil current (the driver and coil basically act like a switching step-down power supply). Also, if the supply voltage is very high compared to what the motor needs to achieve the set current, the duty cycle will be very low, which also leads to significant differences between average and RMS currents.

Schematic Diagram

 

Schematic diagram of the md09a A4988 stepper motor driver carrier with regulators.

 

Note: This board is a drop-in replacement for the original (and now discontinued) A4983 stepper motor driver carrier with voltage regulators. The key difference is that the newer A4988 offers overcurrent protection that the A4983 lacks; it is otherwise virtually identical to the A4983.

問與答

目前沒有任何商品問答!
本商品上架日期:2013-05-28.
評價
建議購買的商品清單!可以參考看看喔
TINY85 USB Micro 開發板 For Arduino®
TINY85 USB Micro 開發板 For Arduino®
42步進電機(Planet Gear Stepper Motor)42BYGH40兩相步進電機FIT349
42步進電機(Planet Gear Stepper Motor)42BYGH40兩相步進電機FIT349
購物車 更多
1 x 總覽:樹莓派【DEXTED原廠】【Arducam原廠】
1 x ●VGA免焊接頭DB15公頭3排15針15P插頭 (全通)VGA3+9 公頭無殼
1 x ●40P 20cm 彩色排線 母-母 / 雙母 / 母對母 散頭 杜邦線 (PIGO)
1 x *MCP3008 (IC) 料
1 x (售完*) RedBearLab原廠(台灣獨家代理)BLE Shield V2.1開發板/Bluetooth Low ..
1 x ●1.27MM FC-14P雙頭線 14pin針 JTAG連接線 AVR下載線 IDC灰排線 (10CM) 2X7Pin
1 x Pololu DRV8835 Dual Motor Driver Kit for Raspberry Pi B+(PI2753
1 x ●&LattePanda V1(2G/32GB),強大的 Mini PC 電腦開發板 (DFR418)Win10(已激活/帶授權
1 x ▼●(特價,現貨)手動脹管器 6mm-22mm 銅管脹管器 空調維修 銅鋁管擴口器製冷工具 (WK-622) 送精品絞刀
1 x 樹莓派【乙太網】總覽
1 x ▽●(現貨*)LittleBits 原廠 Synth Kit 合成套裝/12塊模組
1 x &【加購品】:導軌底座、底殼,電流模組 過電流保護 等專用模組可加購
1 x 4.2inch e-Paper Cloud Module模組,4.2寸 電子墨水屏模塊 400×300
1 x ●福岡老虎鉗(FO-1403/8寸-省力鋼絲鉗),多功能萬用 鋼絲鉗 德國進口款 電工鉗子工具
1 x DC4V-36V 轉DC4V-60V 電動車大功率直流升壓器1000W
1 x (書+元件送工具)模擬和數字電路實驗套件麵包板電子製作68例
1 x ●(美國製) (10x2 2.54mm)JTAG to SWD(10P 5x2 1.27mm)轉接板(ada2094)
1 x #Pi3B+ Pi4B Pi5專用 High Quality Camera HQ高清變焦攝像頭 壓克力外殼I款,DIY相機神器
1 x AT89S8253-24PC
1 x (RLY-8-PoE-RS485) 8路網絡控制繼電器模塊(支持PoE和RS485)DFR290
1 x 3.2inch RPi LCD (B) Raspberry Pi 樹莓派顯示屏320x240清晰度顯示
1 x &▽●(現貨*)Micro:bit智能小車機器人套件Microbit圖形化編程開發板(不含主板)
1 x ●Raspberry Pi NoIR Camera V2.1 夜視攝像頭影音模塊 800萬 IMX219、JETSON NANO
1 x LattePanda V1 專用 鋁合金外殼散熱風扇Cooling Fan(FIT504)
1 x 手動脹管器 6mm-22mm 銅管脹管器 空調維修 銅鋁管擴口器製冷工具 (飛越脹管器) 送筆試絞刀
1 x #&●(現貨)2022新品 Raspberry Pi Pico H 高性能微控制器板 RP2040 開發板
1 x ATMEGA48V-10PI
1 x &●(現貨供應)最新版 BeagleBone Black(Rev C)TI AM3358ARM Cortex-A8 狗骨頭
1 x Jetson Nano Developer Kit (配件包 C),高大上AI開發板 配件:7寸IPS屏、攝像頭、64G、電源
1 x WeMos D1 MINI ( ESP-32S ) 迷你ESP32 WiFi +藍牙物聯網
1 x ●SJ-230C 壓接鉗 0.5-1/1.5-2.5/4-6 mm2,適用於插簧及連接端頭
1 x &●Arduino® Mega2560 Rev3 R3 ATmega2560 (A000067)(義大利原廠)
1 x ●AD7705 雙路16位ADC數據採集模塊(不焊4pin),輸入增益可編程SPI接口
1 x Sparkfun原廠 Joystick Shield - Bare PCB(DEV-09824)
1 x $BBC Doctor Who HiFive Inventor Kit (基本套件) (DEV-17596)
1 x SMT Breakout PCB for 44-QFN or 44-TQFP 3Pack(ada1162)
1 x $請先詢價(預購)UDOO BOLT V8 開發板, 嵌入式 V1605B 四核 8線
1 x W77E516A
1 x >(預購)2016新款 BeagleBoard X15 狗骨頭 AM5728 2×1.5-GHz ARM Cortex-A15
1 x $請先詢價 UDOO Dual Basic 基本款
1 x Allo系列 PIANO DAC 音頻模組 樹莓派
1 x (RS485輸出模塊5V)電子秤稱重採集模塊 變送器重量放大器 RS485 TTL串口通信Modbus
1 x 時立 1080P 全高清HDMI 外置錄製盒 錄寶Min(小盒子)
1 x EPEC2023編程控制器
NT$110,196,433
查詢訂單狀態
 
請輸入您的訂單編號
商品通知狀態 更多
通知A4988 步進馬達驅動板 含穩壓 Stepper Motor Driver Carrier with Voltage Regu
更新時通知我
推薦給朋友
 
推薦這個商品給朋友

聯絡方式:手機:0933807110 或 0968222607
E-mail:[email protected](主要信箱) & [email protected](次要) & [email protected] & [email protected] & [email protected]